Zhaga DMXcas
Casambi 8-Channel DMX Dimmer/Receiver with Fanstel Long Range Radio
Zhaga DMXcas is a Bluetooth controllable, Casambi enabled, eight channel DMX-512 dim-mer that allows connection of a standard DMX-512 master controller to a Casambi network. While the casDMX is intended to connect to fixtures, the DMXcas is the “other side”, allow-ing for standard DMX controllers to be utilized with Casambi networks. The DMXcas is con-nected between a 12-24 VDC Class 2 power supply, and a DMX master.
DMXcas can implement up to eight Casambi pushbutton devices, making it an ideal part-ner for RGBW and tunable white (TW) applications. Multiple DMXcas devices can be used in the same network to control different fixtures, channels or zones since the eight chan-nels of control can be mapped using the Casambi mobile application.
DMX can be configured with the Casambi app which can be downloaded free of charge from Apple App Store and Google Play Store. The unit acts like a Casambi button, and can be mapped to a fixture or channel.
Different Casambi enabled products can be used from a simple one luminaire direct con-trol to a complete and full featured light control system where up to 250 units form auto-matically an intelligent mesh network.
INPUT
Voltage range: +8-24 VDC, Class 2
No-load input current: 30 mA
DMX-512 OUTPUT
3-wire non-isolated DMX-512
RADIO TRANSCEIVER
Fanstel BT840 Radio Module
Operating frequencies: 2.401-2.483 Ghz
Maximum output power: typ. +3.4dBm
-103 dBm RX sensitivity in long-range mode
OPERATING CONDITIONS
IP66 (non submersible) Ambient temperature, ta: -13…+113°F (-25…+45°C)
Max. case temperature, tc: +167°F (+75°C)
Storage temperature: -13…+167°F (-25…+75°C)
Max. relative humidity: 0…80%, non-cond.
RECOMMENDED INTERFACE CONNECTOR
TE Zhaga 40mm Book Z10 Connector
TE Lumawise Endurance S mating connectors: 2343403-1, 2363638-2 or 1-2363638-2
TE X10 CONNECTOR SIGNALS
Pin 1 = 12=24VDC
Pin 2 = Ground (share with DMX ground as well)
Pin 3 = DMX+
Pin 4 = DMX-
INSTALLATION DETAILS
Connect a Class 2 power supply with 12-24 VDC output voltage to the input connector of the Zhaga DMXcas. Make sure not to use a constant current LED driver and make sure that the cable polarity is correct. The product has one DMX universe, with a DMX+ and DMX– connection, plus a ground. Connect the DMX load wires accordingly to a DMX master of your choice to give you DMX control of your Casambi lighting network.
Zhaga DMXcas can be mapped just like pushbuttons are mapped in the Casambi application. Once you add the Zhaga DMXcas to your Casambi net-work, navigate to the “More” button at the bottom of the app. Then press “Switches:, where the Zhaga DMXcas will be seen. Press on the Zhaga DMXcas that you want to configure, and select each of the eight pushbutton items in turn. Then configure each of the eight pushbuttons to control a Casambi element by pressing on “Not in Use” .and then select what the pushbutton is to control, most likely “Controls and Element”, which then you can select a certain element to control. Be sure to press “Done” at the top right to save the configuration.
Zhaga DMXcas should not be placed in a metal enclosure, such as metal junction boxes. Metal will attenuate radio signals which are crucial to the op-eration of the product. If the product will have to installed into a junction box, make sure to use a plastic junction box.
Zhaga DMXcas is an ETL Listed Open-Type device which means that it will have to be used together with a Class 2 power supply with maximum output power of 100 VA. The product can be installed outside of junction box. Make sure to comply with National Electric Code in installation and when se-lecting installation wires.
40mm Book 18
RANGE DETAILS
The range between two Zhaga casDMX’s or between a Zhaga casDMX and a mpbile device can vary depending on obstacles and surrounding material. The open air range between two Zhaga casDMXs can be in excess of 200 feet, but if the unit is encapsulated into a metal structure, the range can be only few feet. The mobile device can be the range limiter when connecting it to the Zhaga casDMX. Thorough testing is high suggested.
Casambi uses mesh network technology so each Zhaga casDMX acts also as a repeater. When testing the network, it is important to test that each unit can be controlled from any point of the network covered area.
COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Warning
Changes or modifications not expressly approved by DMX Engineering and Design LLC could void the user’s authority to operate the equipment.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement for Canada
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment is exempt from the routine RF exposure evaluation requirements of RSS-102. This equipment should be installed and operated with a minimum distance of 20 cm between the antenna and the user or bystanders.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions sui-vantes:
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Ce matériel n’est pas sujet à l’évaluation habituelle d’exposition RF selon RSS102. Ce matériel devrait être installé et exploité en gardant une distance minimale de 20
